PDA

View Full Version : NLTS in an EVO 6

REWINDNOTTM
09-10-2009, 07:29 AM
I have a running EVO7 ECU in a EVO6.

I understand that the evo 6 does not have the clutch switch required to make this work, does anyone have a wiring diagram and a tutorial so I can install one.

Thank you
Rasteirinho
09-10-2009, 09:40 PM
The best thing you can do, assuming the E7 has the clutch switch, is to have a look to the wiring diagram of the E7 and also have a look to how the switch is installed in a E7.

That's what i would do...
REWINDNOTTM
12-10-2009, 09:39 PM
I understand that the clutch switch on the evo7 ecu goes into pin43

I don't have access to a evo7 to investigate the clutch switch.

What switches are other people using? Is the switch installed on the top or bottom of the pedel, is there a 'how to' guide or tutorial?
lee_r_one
12-10-2009, 10:09 PM
Sorry for being dumb but define NLTS for me please?
lee_r_one
12-10-2009, 10:13 PM
ah no lift to shift der
starkers
12-10-2009, 10:15 PM
NLTS = No lift to shift

Basically you can keep your foot planted to the floor on gear changes:smile:
lee_r_one
12-10-2009, 10:19 PM
am sure this is just a link from ecu to n/o switch on clutch pedal
lee_r_one
12-10-2009, 10:21 PM
so should be pin 43 though pedal switch then to ground/body/earth????
lee_r_one
12-10-2009, 10:26 PM
so long as it is enabled in the rom
REWINDNOTTM
12-10-2009, 11:10 PM
So is the switch existing and just needs wiring up?

What's n/o?
lee_r_one
13-10-2009, 07:54 AM
No i think you need to add a switch like a brake light switch.
n/o is normally open so no connection then when switch is operated it goes closed causing a connection.
REWINDNOTTM
13-10-2009, 09:39 AM
brake light rould be the easist to source.

Have anyone done this? what are other people experiences?

also just out of interest is the Launch control, controlled by the clutch switch or activated by speed (or lack of?)
starkers
13-10-2009, 02:44 PM
BarryC on the MLR fitted a clutch switch and did a 'how to' with pics but just searched to find the pics have now been removed so not much use anymore..... Could be worth sending him a PM though
REWINDNOTTM
13-10-2009, 03:24 PM
BarryC on the MLR fitted a clutch switch and did a 'how to' with pics but just searched to find the pics have now been removed so not much use anymore..... Could be worth sending him a PM though

i did see that... i have to contact him i think

thanks

REWIND
lee_r_one
13-10-2009, 08:33 PM
connect one side of the switch to chassis ground
the other side to pin 43 on the evo 7 ecu
it is not possible to connect this to a 3 plug evo 8 ecu as there was no OEM input assigned for a clutch switch

661

662

663
starkers
13-10-2009, 08:43 PM
Posted now by BarryC on the MLR:smile:

http://lancerregister.com/showthread.php?t=287035
lee_r_one
13-10-2009, 09:09 PM
brake light rould be the easist to source.

Have anyone done this? what are other people experiences?

also just out of interest is the Launch control, controlled by the clutch switch or activated by speed (or lack of?)

It is set to what rpm you want in the rom under stat rev limit and is controlled by speed which can be set under stat rev limit speed threshold:smile:
REWINDNOTTM
14-10-2009, 07:07 PM
You guys beat me to it... I was just about to post the info..lol