PDA

View Full Version : Load is still not recording a valid figure

Leecavturbo
12-03-2009, 10:27 PM
anyone know why my loads max out? my load no matter how logged is 255
once on boost above 1 bar.
even logging via logworks reports 5v which is the max
GrayW
12-03-2009, 10:52 PM
Are you using 1 byte.
AndyF
13-03-2009, 08:11 AM
Graham,
If it's maxing out at 255 then he must be using 1 byte as that's the equivalent of FF in hex which is that max single byte figure.

Andy
Leecavturbo
13-03-2009, 10:35 AM
i'll do some logs again today i forget whats whats
GrayW
13-03-2009, 04:19 PM
1 byte goes higher than that, I have logs from my car.
AndyF
13-03-2009, 06:15 PM
It can't be a true 1 byte then!!!! 1 byte = 8 bits = max binary value of 11111111 = FF in hex = 255 in decimal ;)

Unless there is a conversion factor applied in your logs
GrayW
13-03-2009, 06:26 PM
<DataListItem DataLog="Y" Color="" Display="Load 1Byte" LogReference="Load1B" RequestID="41" Eval="1.2*x" Unit="load" MetricEval="" MetricUnit="" ResponseBytes="1" GaugeMin="0" GaugeMax="270" ChartMin="0" ChartMax="270" ScalingFactor="1" Notes="" Priority="1" Visible="False" />
Leecavturbo
13-03-2009, 06:53 PM
what he said^ :tt2:
scandinavian flick
13-03-2009, 07:09 PM
Brilliant value them few posts.... Geek City!

Shame I don't get it!

J
burgers22
13-03-2009, 08:35 PM
There is a 2 byte to 1 byte conversion factor in the tephra mods section, mines set to 1:2 maybe this has been changed?
Leecavturbo
14-03-2009, 10:25 PM
ok gray i logged 1byte (Load11bit4) and it deffo tops out at 255
and just stays there above 1 bar
so whats up :confused1:
GrayW
14-03-2009, 11:49 PM
Post the actual rom you are using on the car.
Leecavturbo
14-03-2009, 11:55 PM
sent just
GrayW
15-03-2009, 12:08 AM
All fixed and on it's way back:D
Leecavturbo
15-03-2009, 12:09 AM
cool. so log which load gray now?
GrayW
15-03-2009, 12:17 AM
Log 'Load 1Byte' on the pick list, not (Load11bit4).
wip
15-03-2009, 04:23 PM
Hmmm....

http://forums.evolutionm.net/ecuflash/402394-1-byte-load-not-right.html

:smile:
GrayW
15-03-2009, 04:30 PM
He had not set the MUT request 41 up for 1 byte load, it works fine, been using it for months.
GrayW
15-03-2009, 06:00 PM
Have you tried it yet Lee?
Leecavturbo
15-03-2009, 06:16 PM
no. give me 15mins
Leecavturbo
15-03-2009, 06:21 PM
sitting in car right now. evoscan doesn't list 1byte!
GrayW
15-03-2009, 07:19 PM
Have you added the line from 7 to the data.xml under evoscan?
Leecavturbo
15-03-2009, 07:21 PM
Have you added the line from 7 to the data.xml under evoscan?

missed that will do.
GrayW
15-03-2009, 07:23 PM
<DataListItem DataLog="Y" Color="" Display="Load 1Byte" LogReference="Load1B" RequestID="41" Eval="1.2*x" Unit="load" MetricEval="" MetricUnit="" ResponseBytes="1" GaugeMin="0" GaugeMax="270" ChartMin="0" ChartMax="270" ScalingFactor="1" Notes="" Priority="1" Visible="False" />
Leecavturbo
15-03-2009, 07:29 PM
everything starts with <table but the code above doesn't!
?
Leecavturbo
15-03-2009, 07:31 PM
cancel found it
Leecavturbo
15-03-2009, 07:33 PM
does the 'Y' denote default item to log?
Leecavturbo
15-03-2009, 08:42 PM
yep works 235 load = 1.25 - .3 bar. sound correct amundo?
caesarson
16-03-2009, 12:42 PM
:>'s just added the 1 byte table into EVO Scan. So is this a more accurate way to log then 2 byte load.
GrayW
16-03-2009, 12:48 PM
It's only as the 2 byte load address for 96260009 was not available when I was looking.
caesarson
16-03-2009, 12:53 PM
before i ask the dumb question of 'can 2 byte logging be used with a non Tephra ROM'

Has anyone got the 2byte thread from EVOm, or another good one.

Thanks